Category Archives for Engine

2000-01 VALVE COVERS 5.4L V8 – VIN L

Removal (Expedition, Navigator & Pickup – Left) 1. Disconnect negative battery cable(s). Remove air cleaner. Unbolt power steering reservoir bracket, and position reservoir and bracket assembly aside. 2. Disconnect PCV hose from valve cover. Disconnect control cables from throttle body. … Continue reading

01. July 2018 by sam
Categories: Engine | Leave a comment

2000-01 CYLINDER HEAD 5.4L V8 – VIN L

Removal 1. Remove the engine. See ENGINE . Remove the flexplate or flywheel. Mount the engine on a suitable work stand. Remove exhaust manifold. See EXHAUST MANIFOLD . 2. Remove timing chains. See TIMING CHAINS . Remove cylinder head bolts … Continue reading

01. July 2018 by sam
Categories: Engine | Leave a comment

2000-01 EXHAUST MANIFOLD 5.4L V8 – VIN L

Removal Raise and support vehicle. Remove front fender splash shield. Remove wheel opening molding on 4WD models. If removing left exhaust manifold, remove EGR manifold tube and brake vacuum booster hose bracket. On either side, disconnect exhaust manifold flange. Remove … Continue reading

01. July 2018 by sam
Categories: Engine | Leave a comment

2000-01 INTAKE MANIFOLD 5.4L V8 – VIN L

Removal 1. Disconnect negative battery cable(s). On vans, remove engine cover. On all models, release fuel pressure and disconnect fuel lines. See FUEL PRESSURE RELEASE & FUEL LINE CONNECTIONS . 2. Drain cooling system. Disconnect upper radiator hose from thermostat … Continue reading

01. July 2018 by sam
Categories: Engine | Leave a comment

2000-01 ENGINE 5.4L V8 – VIN L

Removal (Expedition, Navigator & Pickup) 1. Disconnect negative battery cable. Remove hood. Remove air cleaner assembly. Remove accessory drive belt. Drain cooling system. Remove radiator. Discharge A/C system using approved refrigerant recovery/recycling equipment. Release fuel pressure and disconnect fuel lines. … Continue reading

01. July 2018 by sam
Categories: Engine | Leave a comment

2000-01 FUEL PRESSURE RELEASE & FUEL LINE CONNECTIONS 5.4L V8 – VIN L

1. Remove fuel cap to release fuel tank pressure. Connect EFI Pressure Gauge to relief valve on right rear corner of fuel rail. Release pressure using valve on pressure gauge. 2. Before disconnecting fuel lines, disconnect negative battery cable. To … Continue reading

01. July 2018 by sam
Categories: Engine | Leave a comment

2000-01 OIL PUMP 4.6L V8 – VIN W & 6

Removal Remove oil pan and pick-up tube. See OIL PAN under REMOVAL & INSTALLATION. Remove timing chains and crankshaft sprockets. See TIMING CHAINS under REMOVAL & INSTALLATION. Remove retaining bolts, and remove oil pump. Installation To install, reverse removal procedure. … Continue reading

01. July 2018 by sam
Categories: Engine | Leave a comment

2000-01 ENGINE LUBRICATION SYSTEM 4.6L V8 – VIN W & 6

Rotor-type pump is driven by crankshaft and delivers pressurized oil to main gallery. Crankcase Capacity On vehicles with automatic transmissions, crankcase capacity is 6.7 qts. (6.3L). With manual transmissions, crankcase capacity is 6.5 qts. (6.1L). Oil Pressure With engine at … Continue reading

01. July 2018 by sam
Categories: Engine | Leave a comment

2000-01 CYLINDER BLOCK ASSEMBLY 4.6L V8 – VIN W & 6

Piston & Rod Assembly Note direction of connecting rod installation on piston. Install piston and connecting rod in engine, with notch on top of piston toward front of engine. See Fig. 20 or Fig. 21 . Fitting Pistons 1. Standard … Continue reading

01. July 2018 by sam
Categories: Engine | Leave a comment

2000-01 CYLINDER HEAD OVERHAUL 4.6L V8 – VIN W & 6

Cylinder Head Check cylinder head for cracks or damage. If maximum warpage exceeds .004″ (.10 mm), replace cylinder head. Valve Springs Inspect valve spring free length, out-of-square and pressure. Replace valve spring if not as specified. See VALVES & VALVE … Continue reading

01. July 2018 by sam
Categories: Engine | Leave a comment

← Older posts

Newer posts →